![Flexx Handlebar Factory-Fresh Kit - 35mm](http://fasstmtb.com/cdn/shop/files/IMG-6267_{width}x.jpg?v=1697117880)
Flexx Handlebar Factory-Fresh Kit - 35mm
Our Factory Fresh kits create an easy way to service your Flexx MTB Handlebar. This kit provides you with all of the necessary parts to perform the service.
The Factory Fresh Kit contains contains: 2 bolts, 2 nuts, 4 pin end caps, compression and rebound elastomers, 2 pivot pin bushings, vice jaws, pin catcher, brass pin pusher and M6 bolt.
Just like your suspension, elastomers do need to be freshened up. We recommend changing your elastomers yearly to be sure your Flexx Handlebars are performing as intended.
1. ALL-INCLUSIVE KIT
Comes with everything you need to get your bar ready for another few hundred hours of ride time!
2. WE WILL SERVICE IT FOR YOU.
We will service your Flexx Handlebar for free with the purchase of our Factory Fresh Service Kit. Please call or email us for an RA# if you would like us to service your Flexx Handlebar.
3. SERVICE IT YOURSELF
Read the steps necessary and watch our video under the Service tab above, to install your Factory Fresh kit yourself.
BLUE: XC/Gravel, youth, lightweight riders, 140lbs or less
YELLOW: XC/Trail/mild Enduro, 140-165lbs
RED: Enduro/DH, 150lbs - 220lbs, most popular set up
BLACK: DH 190lbs +-
A properly tuned Flexx Handlebar should feel natural while riding, absorbing small bumps, chatter and other trail terrain that tends to make your hands and upper body more fatigued. Any diving sensation, bottoming out or "that doesn't feel right" is an indication your set up is too soft.
*The pin end caps do not need to be removed to change elastomers, use blue loctite on the nut and bolt when re-assembling We recommend our Fiber Bushing Removal Kit if you need to replace the fiber bushing in the pivot pin.
We offer our free Factory Fresh in-house service program for your Flexx Handlebars. This service requires you OBTAIN an RA# from us, as well as read, print and sign our Service Order Form. Next ship us your bars with the RA# and signed release form, Attn: Factory Fresh. The Factory Fresh service program for Flexx Handlebars is free with the purchase of a Factory Fresh Kit. The Factory Fresh program consists of disassembling and cleaning your Flexx Handlebars, a thorough servicing of the pivots and reassembly with a Flexx Handlebar Factory Fresh Kit. The Factory Fresh Kit contains contains 2 bolts, 2 nuts, 4 pin end caps, pivot bushings for the pivot pin, and your choice of Rebound and Compression Elastomers. Please note that this is only a clean and lube job, in no way does this make your handlebar stronger, last longer or take away any prior damage/neglect. If your Flexx Handlebar is damaged in anyway we will inform you of the damage and what your options are. We will not return damaged handlebars to you as it is a safety concern and liability to yourself.
Two Things To Remember:
1. Do not mix the pivot pins up. The left pin needs to go back in the left hole, and the right pin in the right hole. We separate our pins and hone our pivot holes to .0001 of an inch. It is crucial to have proper fitment of each pin so there is not front to back play.
2. The second key point is do not strike the pivot pin directly with a hammer, press, or any other tool. The best way to protect the pivot pin from "mushrooming" is to use an old M6x1.0 bolt threaded into the pivot pin. Use the bolt to push the pivot pin out.
Tools Needed:
- 4mm Allen Wrench - To change elastomers
- 3mm Allen Wrench - To remove pin end caps if necessary
- Blue Loctite
Servicing your Flexx Handlebar can be done on or off the bike. Be sure if you do place the Flexx Handlebar in a vice you use plastic jaws or a similar product to protect the Flexx Handlebar from being damaged by the jaws.
- Remove the elastomer nuts and bolts, then remove the elastomers.
- Remove the pin end caps with a 3mm allen.
- Now drive the pins completely out. Again, use a M6x1.0 bolt to protect the pin.
- With pins out you can press the pivot bushings out of the bore. A long 6mm socket can typically be used.
- Clean pivot bores and pins.
- Place the pivot pin in the back side of the bar, square to the bore. You will know the pin is square to the bore when it will not rock easily up, down, or to the side without applying force.
- Align the handle bore with the center section bore then press the pivot bushing through both components.
- Protecting the pivot pin with the m6x1.0 bolt threaded into it, tap the pivot pin all the way through the bore flush with the other end.
- Install the pin end caps, use blue Loc-tite on both the male and female threads. Torque the pin end caps to 4nm with a 3mm allen.
- Install the compression elastomer. Butt the 45* relief in the narrower part of the elastomer up against the handle.
- Install the rebound elastomer on the nut.
- Apply blue Loc-tite to the threads of both the bolt and nut. Only use the torx head to hold the bolt when turning the 4mm nut. The bolt will bottom out in nut, bring the handle to 5* up-sweep.
Proper Handle Resistance:
Your handles may have some drag or resistance when the elastomer is removed. The drag is caused by the exacting tolerance required for the Flexx Handlebar to offer the utmost in control and reliability. Flexx Handlebar pivot points are most likely the most exacting tolerance on your entire machine and must be so. Too large of a tolerance will not the yield the precise control you as a rider require to perform at your best. It is not only acceptable but preferred to have some drag on the handles. Each side of every Flexx Handlebar System is measured with a strain gauge to be sure the resistance of each handle is within our tolerance. If your bar rebounds to its present ride height after being compressed you should be good to go. If you have any questions concerning this please contact us. *If your pivot pins are damaged they will need to be replaced. A Pivot Pin kit is an additional $20. Download the Service Order Form
- 2 bolts
- 2 nuts
- 4 pin end caps
- Compression and rebound elastomers
- 2 Igus bushings
- Vice jaws
- Pin catcher
- Brass pin pusher
- M6 bolt.